the old culture from balinese and all i know will show in this blog

Compare hotel prices and find the best deal - HotelsCombined.com Join anandadeknik's empire

Thursday 10 September 2009

How To detect a broken motherboard and how to fix it

Please read carefully for understanding what the meaning below! ^_^

Main board (motherboard) is the circuit board where a variety of connected electronic components such as microprocessors and memory (RAM, ROM, BIOS) and other controller chips and commonly abbreviated with the motherboard.
Okay Jump aza ya! symptoms and how to overcome a broken motherboard:
Dead Total
Check the power supply: In a state in the power cable from the power supply off, disconnect the cable socket mounted on Atx1 Mainboard. Once separated, attach the power cable back, connect / cable shortkan green, black cables, check that the power supply fan spinning? If the spin is a good power supply. Back off the power cord and plug it in again this Atx1 cable to the motherboard.
Check the Clear CMOS Jumper, whether in position or Free Clear, usually when a new motherboard, CMOS jumper position on Clear position.
Check IC chipset in connected and in the Switch On, whether or not excessive heat, over-heat means the chipset is already damaged. CMOS ICs for parts so far are not sold freely.
Also check whether the switch on its functioning.
Motherboard dismantle it carefully, you try to wear clean thinners, if you can not use thinners bottle is in the can. After you dry clean.
Replace IC regulator which is located around the ATX power socket on the motherboard.
Replace the capacity Elko 1000 s / d 3300 uf / 10 Volt, located around the ATX power socket on the motherboard. Be careful to make sure the dismantled components plug the power cable not connected to electricity.
Flame But Not Shown
Try to look and listen if there is sound or beep sound. If there is, there is usually damage the processor, memory and VGA.
Check Processor, you try to hold the refrigeration if excess heat or cold? If it means overheating the processor fan is not working properly then you will change, but if the cold means the processor does not work aka damaged.
Check memory, if memory is usually broken voice on the speaker beep 3 times. Dead, pull the pin clean memory using a pencil eraser to clean, and then plug it in again. If it means there's still broken one of his damaged IC.
Check VGA Card, VGA Card pull, in a state of dead / off try you press, there is less chance your entry or try to wash the feet / her pin. If the VGA card using the fan, clean the fan.
If it still does not appear you are trying to check maybe the monitor is not a flame, to make sure that broken monitor or CPU, you try to press keys on the keyboard NumLock, whether it NumLock light a flame or not. If the flame is damage to the CPU.
Which became the standard when repairing my computer, I always clean out the dust, whether it's motherboard, memory, cdrom, floppy disks, etc., because it is so what else could affect the computer in a dirty / old is not cleaned. But you must be careful in the process and do not rush.

Hang And Often Off / Restart (Reset) Alone
Check the Power Supply, try another power supply is still restart itself or hang. If the power supply was replaced by normal / good, power supply means there is a problem. Replace it if it can be fixed because I myself was not sure if it was still able to function properly, because the power supply is a vital component. Especially for the current price sanggat cheap power supply, I suggest changing it.
Check if there is virus, anti-virus program should always be installed and enable its auto protect. I used to use Norton Anti virus. You should frequently update your antivirus because if there is a new variant virus, anti-virus and you will eliminate the virus mendetect.
At the moment there hangs and blue screen messages like "vxd error at address ...", there is usually a problem in memory. Clean memory is like a step above.
Try to reinstall Windows.
If it still hangs / restarts itself trying to check on your motherboard, you will notice the physical changes, especially components Elko / capacitor, a black round no writing in capacity between 1000 uf/10Volt s / d 3300 uf/10 volts, usually seen, if the damaged looks bloated / swollen and leak or rust.
CMOS Checksum Failure (Low Battery)
Symptoms of damage & Solutions:
CMOS failure message appears (The damage to the CMOS battery, replace battery)
Setting the date, time and other configurations in the BIOS to change (When the battery is replaced, re-do the settings in the BIOS).
Thanks for reading and visit my site!!! i hope this will be help someone , if there is something problem, thanks

regards : I made Ananda Yoga.

3 comments:

Unknown said...
This comment has been removed by a blog administrator.
Unknown said...

The motherboard for me must to be efficient, quality and of course with a reasonable price. That is why costa rica homes for sale i think is the best option in the market if you want to know a beautiful country and to a get a house quality.

bali-dreamland said...

Oh' really??